Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to rot or rust like timber and aluminum.

It is essential to clean and oil UPVC doors and windows regularly. This will save you from costly repairs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and even be fatal. It is essential to make sure that your windows are in good working order.

For single pane windows it can be relatively simple to replace windows, and the new one is usually able to fit into the frame that was previously installed easily. However when you have double-pane windows that are anchored by internal beading, it'll be more difficult to get rid of the old panes and put in new ones. In this case, you will need to locate some plastic spacers to aid the new pane in being able to fit perfectly into the window frame.

If you plan to try to remove the glass panes yourself, it is essential to wear the proper safety gear, including thick gloves and protective eyewear. It is also recommended to lay down a dropcloth prior to you begin working on the window panes, so that any shards fall on the fabric, upvc Window Repairs not onto the floor which could cause them to be trampled under.

Once the glass has been removed and the glass is removed, it's a good idea to seal the gap with clear packaging tape or duct tape to stop drafts and water from entering the home until a professional comes out and fix the window. This will also provide an obstruction to prevent intruders from getting into your home. If the gap is large, you might be interested in the security door with an integrated window, since it offers the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable energy efficient, durable and long-lasting alternative to timber sash windows. However, over time they can suffer from a variety of issues like sagging. A window repairs that is sagging can cause problems with light, draughts, and even security. It's crucial to act as soon as you discover that your uPVC windows are sagging.

To fix a window that is sagging you can try repositioning the hinges. First, you'll need to open the windows to access the frame. After that, using a screwdriver, you can take off the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after having relocated your hinges. If you're satisfied with the fit, you can tighten the screws to ensure they remain in place.

If you are unable to reposition the hinges you may require replacing the seal. As time passes, rubber seals lose their elasticity and dry out which causes them to lose tightness. It is crucial to replace your seal as soon as you can in order to keep your uPVC window watertight and draughtproof.

uPVC handles can also become loose. Most often it is due to screws that have come loose over time. However, it can be due to the fact that the handle mechanism has been worn out. It's relatively easy to fix a loose uPVC hand. The first step is to close your window and do an experiment to ensure that it fits. The joint at the corners of the sash should be aligned with the joint on the casing. If it isn't, you can use the screwdriver to loosen the handle. Then, turn the mechanism to position.

3. Water Leaks

If you awake to wet floors and damp walls every time it rains it's crucial to take action. The leaks of water through windows could cause structural damage to your home and impact your ability to regulate the temperature of your home. The most frequent reason for leaks in uPVC windows is that the sealant surrounding the frame is damaged or missing.

This is an easy fix that can be accomplished by any DIYer who is competent. Depending on how severe the issue is, the old caulking might need to be removed. It is important to keep in mind that when it comes to uPVC window repairs, you should not be tempted to 'over-caulk and then make the area harder to clean and can reduce your energy efficiency.

Check that any drainage holes do not have debris inside them and ensure that the sill pan is properly angled to allow the water to drain from the window. In more serious situations, you might need to consider replacing the window.

Mold spots and rotted sills are another sign of water leakage. This fungus thrives under humid conditions and can propagate quickly throughout the home.

If the leakage is occurring between the double-glazed glass it is more likely the problem is with the seal rather than the frame. A uPVC specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your upvc window repairs windows are difficult to open, or are loose and blow open with ease It could be hinges at the fault. Any competent DIYer can replace hinges in just a few minutes.

Like any mechanical component hinges are prone to wear out over time. The process of replacing a hinge on a window is essentially a simple procedure, but it is easier to do with someone else to assist in holding the frame up.

Check that the uPVC hinges are open and closed in the right direction. This can be done by looking for the arrows on each hinge. This indicates which way the window should be opened.

The issue could be caused by opening the window incorrectly or due to a poor installation at the factory. Sending us a picture through our website can often solve the issue. We are always happy to offer advice.

It is also essential to lubricate the hinges on a regular basis. This can be done by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regularly lubrication will help the window operate and close more easily. It can also lower the possibility of a window sticking and help prevent corrosion. The ideal time to do this once a year. WD40 and other solvent based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a variety of various factors. The hinges can also be unbalanced due to wear, creating an opening between the frame and sash. If they are beyond repair, it might be necessary to get them re-aligned. The second is the interlock, which is located on the hinge of the window, can also become misaligned, again it is possible to just give them a clean but in some cases it might be necessary to have them replaced.

The next most common reason for draughts are the window seals. These are susceptible to being worn out or damaged over time, and allow air to escape through these gaps. Replacement of these with high-quality weatherstripping can help keep draughts at bay. Replace the windows made of upvc with low-emissivity glasses. This will help control indoor temperatures, and reduce the risk of draughts.

Another method of reducing the amount of draughts is to use a Draught-exclusion device. These are usually fabric tubes filled with a filler that can be hung over your window sill. These will help to keep cold air out and keep your home warm and cozy!

Your windows made of upvc will remain a great source of insulation and security in your home with regular maintenance and repairs. It is important to remember that all windows eventually wear out and it is more cost-effective to simply replace them rather than repair them. If you are experiencing issues with your Upvc windows, it is always best to seek professional assistance immediately.