Repairs to uPVC Windows

uPVC is an excellent option for modern homes. They are easy to maintain, durable and long-lasting. As opposed to aluminium and timber they do not get rusty or decay.

It is essential to clean and oil UPVC windows and doors regularly. This will reduce costly repairs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause significant damage to your home and even be fatal. It is important to take the time to make sure that you're doing everything you can to ensure that your windows are in good shape.

Single-pane windows are relatively simple to replace and typically fit into frames of the past easily. If you have double-paned windows that are joined by internal beading, it is more difficult to remove and replace the panes that were previously in use. In this instance, you will need to find some plastic spacers that aid the new pane in being able to fit perfectly into the frame of the window.

If you are going attempt to remove the window panes by yourself, it is essential to wear the appropriate safety equipment, including thick gloves and eye protection. It is also recommended to lay down a dropcloth before you begin working on the window panes, so that any shards fall onto the fabric, not onto the floor and could be trampled.

Once the glass has been removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to block water and drafts from getting into the home until a professional can come out and repair the window. It also acts as a barrier to prevent any criminals from getting into your home. If the gap is large, you might be interested in a security door that has an integrated window, as it will provide the best of both worlds.

2. Sagging

Upvc is a long-lasting and energy efficient alternative to timber sash window. In time, they could be affected by a variety of issues that include sliding. A window that is sagging can cause problems with light, draughts or even security. If you find that your uPVC window is beginning to lose its shape, it is important to act swiftly to prevent the problem from becoming worse.

Repositioning the hinges can help fix a window that is sliding. First, you'll need to open the windows to get at the frame. Then, using an screwdriver, take off the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. Once you've repositioned the hinges, close your window and test it for fitting. If you're satisfied with the size of the window, tighten the screws to hold them in place.

If you are unable to reposition the hinges, you could have to replace the seal. As time passes, rubber seals lose their elasticity and dry out which causes them to lose tightness. It is crucial to replace your seal as quickly as you can in order to keep your uPVC window watertight and draughtproof.

uPVC handles can also loosen up. The majority of the time it is due to screws that have come loose over time. However, it can also happen because the handle mechanism has worn out. It's fairly simple to repair a loose uPVC handle. You'll first need to close the window and perform an experiment fitting. The joint at the corner of the sash must align with the joint on the casing. If it isn't, you can make use of a screwdriver to loosen the handle and return the mechanism to its original position.

3. Water Leaks

It is crucial to act if you awake each day to discover mouldy walls and wet floors. Windows that leak water do not only lead to the degradation of your home's structure but also undermine your efforts to regulate the temperature in your home. Most of the time, window repairs uPVC window leaks are caused by a damaged or missing sealant.

This is a relatively easy fix that can be completed by any skilled DIYer. Depending on the severity of the issue the old caulking may need to be removed before a fresh layer can be put on. It is essential to remember that when it is about uPVC window repairs you should not be tempted to apply too much caulk in order to make the area harder to clean and decrease the efficiency of your energy usage.

Make sure that the drainage holes have no debris in them, and also ensure that the sill pan is properly angled to drain away from the window. In more serious situations, you may need to think about replacing the window.

Mold spots and rotten sills are other signs of water leakage. This fungus thrives under humid conditions and can propagate quickly throughout the house.

It is also important to keep in mind that if the leak originates from the glass of your double glazed window repairs near me glazed windows, it is more likely to be an issue with the glass seal rather than the frame or sagging. A uPVC specialist can fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your uPVC window is difficult to open, or if it opens in a breeze. They can be repaired by any DIYer who is skilled and can usually be completed in just a few minutes.

Like any mechanical component hinges are prone to wear out over time. It's easy to change the hinges on a window however it is easier if someone helps you to hold the frame.

Check that the uPVC hinges are open and closed in the correct direction. Check for the arrows on each hinge to determine which direction the window should be opened.

Window hinges that aren't working properly could be the result of incorrectly opening the window in a certain way or by improper installation in the factory. It is usually possible to fix the issue by sending us a photograph through our website and we will be more than happy to give you suggestions.

Regular lubrication of hinges is also essential. This can be done by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also decreases the risk of a window sticking and help prevent corrosion. It is recommended to do this once a year. WD40 and other solvent based fluids are not recommended since they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different factors. The hinges may also become misaligned due to wear, causing a gap where the sash and frame meet. This can be easily repaired by giving them a good cleaning, but if they are beyond repair it may be necessary to get them aligned or replaced. The interlock may also become disaligned. This happens on the hinge side and might require to be cleaned. In some instances it is possible to replace them.

The second most frequent reason for draughts is window seals. These are prone to wear or damaged over time and will allow air to escape through the gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity lenses. This will help to regulate indoor temperatures and decrease draughts.

Lastly, one of the most effective ways to reduce draughts is by using a draught excluder. These are typically made of fabric filled with some kind of filler. They can be positioned on the top of your windowsill. They will help block out cold air and keep your home warm and cosy!

Your windows made of upvc will continue to provide excellent insulation and security for your home by performing regular maintenance and repairs. It is essential to remember that all windows will eventually get worn out and it could be more cost-effective to simply replace them instead of fixing them. If you are experiencing issues with your Upvc windows, it's recommended to seek assistance from a professional as soon as you can.