How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with an electronic keyless entry system built into. The key is usually akin to an remote control, and can be replaced with a new one from a Kia dealer or locksmith.

Key fobs may stop working for several reasons, including the battery of the coin is dead worn buttons, water damage, signal interference and a malfunctioning receiver module. Here are some guidelines on how to get your Kia Sportage replacement key working again.

How to replace the remote key or smartkey

Whether your kia picanto keys locked in car comes with an intelligent key, remote key, push to start key or a regular non-transponder steel key The battery inside these keys will eventually need replacement. This is particularly when your Car Key Cutting And Programming Price displays a message that indicates the smart or remote keys aren't powered.

Luckily, this is an easy procedure. To replace the key fob battery remove the mechanical key from the hole in the back of the key fob. You then need to remove the cover. A small screw is found inside the key fob, which holds the battery in the correct position. Take out the old battery by unscrewing the screw using the help of a small screwdriver. Then, you can insert the new battery and close the hole in the key fob.

When the key fob is equipped with an updated battery and you've tested it, press the locks and unlock buttons. It's okay If the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or you need to complete errands in Brandon.

Not all key fobs may need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder keys made of steel) are not required for programming. If your key needs to be programmed again, you will need to be aware of the key code written on the tag of the key code and save the number in a secure place.

How do you replace a dead battery?

If the Kia key fob does not respond to pressing the lock or unlock button, it is most likely that the battery is not fully charged. A weak battery can cause other issues, such as the check engine light coming on or the engine not cranking. It is easy to replace key fob batteries using just a few simple tools.

Make sure that you shut off your vehicle and close all doors prior to beginning. Locate the small metal or plastic piece at the bottom of your key fob and jiggle it until a metal key slips out. Then, you can put the key into the handle of the door for the driver to open your car.

To replace the battery on the key fob remove the cover at the rear. Use a pry tool to open the latch that holds the black negative cable. Remove the old battery and Car Key Cutting And Programming Price then orient the new battery so that the "+" positive side is facing you and the "negative" negative side is facing the fob's metal electrical contacts. Push the new CR2032 battery straight into place without putting too much force on it to avoid damaging or breaking the metal contacts.

Once the new battery has been installed then turn the key fob off and then on in the ignition several times until the door locks cycle. You can then test the Kia's key fob to ensure it's working properly.

How to replace a smart keys

You can have a standard keyfob, or a Smart Key based on the model of 2012 kia soul key fob Sportage. The smart key has an embedded mechanical key blade while the standard keyfob does not. Both kinds of key fobs contain batteries inside that eventually will need to be replaced. This is a simple procedure that takes only two minutes.

Be sure to switch off your Kia, and be on a flat or well-lit surface prior to when you begin. Also, keep in mind that there are tiny pieces inside the fob which could be snagged if not vigilant.

The first step is to locate the small release button that is located on the lower backside of your fob. It will be a circular button or a rectangular slot. After pressing this button mechanical key blade, it will be released and you will be able to open the key fob.

Once the key fob is open, remove the battery that was in it. The new battery is C2032, and can be purchased from a local or online auto parts store. When you are done you should be able to lock or unlock your vehicle with your key fob even if the engine isn't running!

How do you replace the mechanical key?

The Kia keyfob can be a fantastic convenience that allows us to lock or unlock our car by pressing a button. As with all devices like a key fob, the Kia can occasionally have problems. There are solutions to resolve these issues and keep your key fobs functioning for many years.

A dead or weak battery is among the most common problems. This can cause your fob to stop working or operate intermittently. If this is the case try replacing the battery with a new one.

If this doesn't resolve the issue you can try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not to scratch any internal components or scratch the plastic. Once the battery is removed, replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the fob to make sure it's functioning properly. Contact a dealer, or a locksmith to fix the issue in the event that the fob is not working. To avoid a lockout in the future make sure you get an emergency key that can work on all trunk and door cylinders.